JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 57
Fig. 14: Example of automating a hand lay application
based on the width and type of material
running through the nip. If the tows are
0.25 inches in width, and the best tension is determined to be 1pli, the operator simply multiplies the width times
the required tension, in this case 0.25
pounds. If, for example, there are 100
tows, each at a tension of 0.25 pounds,
the total tension setpoint should be 25
pounds. If there are 200 tows, the total
tension should be set for 50 pounds.
Fig. 16: Tension controllers
Hand lay-up
Open or closed-loop tension control,
or a combination of both, can be very
useful in hand lay-up applications.
By using a brake on the paper carrier
unwind roll and adding a drive motor to the rewind, it becomes possible
to automate a hand lay-up application. Currently, where a carrier web
is pulled over a table and carbon fibre
or fibreglass pieces are laid out in a
pattern, the web is hand-wound onto a
roll where the finished roll of material
is built. By adding a drive motor to the
wind up and a brake at the unwind roll,
you can run slowly (1 to 2fpm) along
the table, slow enough for the pieces to
be properly positioned, and the web is
constantly wound up.
By adding tension control to the rewind, it becomes possible to build the
rolls with a consistent web tension. If
a poly web layer is required, a closedloop control system can be added,
and the insulating layer of poly can be
added without wrinkles, and will not
Fig. 15: Load cells / transducers
neck down as the rolls cure.
Even if the web is not constantly moving, you can automatically run the carrier sheet the length of the table, stop
the web, and lay out the pattern, and
then wind up the web until the carrier
is clear the length of the table, stop the
web, place the pattern again, and wind
up that portion. Since everything is
under control, the tension throughout
the roll will be consistent.
By controlling the rewind tension,
either open loop or closed loop, it becomes possible to build consistent rolls.
Products
This article has referred to a variety of
products used for precisely controlling
tension, such as load cells, controllers,
Fig. 17: Tension brakes
brakes and nips.
Load cells
Load cells directly measure the tension
of the material the operator is running
(Fig.15). Load cells come in a variety
of styles to best meet the exact needs
of the application but all operate under
the same principle. As the web moves
over the load cells, or the roller they are
attached to, the tension of the materials creates deflection or bend, which
the load cell interprets into an electrical signal that the controller utilizes to
control the torque device. Any changes
in electrical signal represent a change
No99 September 2015 / jec
composites magazine 57
Table of Contents for the Digital Edition of JEC COMPOSITES MAGAZINE - Issue #99 - September 2015
Cover
Edito
Point of view: The future of mass production
Contents
Companies & Business
In brief
Interview UCI - “Our aim is to ensure bicyclers are safe to race”
Agenda of Events
Applications
Recreational aviation - A recreational airplane as advanced as the latest widebodied aircraft
Sports & leisure - Cork, flax and green epoxy: a perfect balance for a skateboard
Medical - Lightweight emergency medical cot
Market
Natural fibres - Tending towards optimism
SPECIAL JEC FORUMS
Interview - MIT-NECST Lab: a research consortium dedicated to composites in Aeronautics
Conferences - Gain insight into the JEC 2015 Forums conferences programme
FEATURE WIND ENERGY
Wind energy - Double-digit growth continues
Design - A wind turbine without blades
Simulation - Visualizing RTM behaviour using advanced 3D CAE technology
Permeability - Optimizing fabrics for wind blade infusion
Automation - Automation strategies in rotor blade production: preforming vs. direct textile layup
Recycling - Recycling decommissioned composite wind blades
Platform - An internet aid for advances in wind turbine blade design
Research & Development
Graphene - Gambling with graphene, will it pay off ?
Thermal expansion - Boeing simulates thermal expansion in composites with expanded metal foil for lightning protection of aircraft structures
Technology & Innovations
Heating - Power transfer in complex shape heated moulds or functional composites
Manufacturing - Tension control in composites manufacturing
3D printing - A fully biodegradable flax fibre-reinforced thermoplastic filament for 3D printing
RTM/LCM - Fast production epoxies for lightweight automotive composites
Index
In the world
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Cover
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 2
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Edito
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Point of view: The future of mass production
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 5
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Contents
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 7
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - In brief
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 9
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 10
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Agenda of Events
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Interview UCI - “Our aim is to ensure bicyclers are safe to race”
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 13
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Recreational aviation - A recreational airplane as advanced as the latest widebodied aircraft
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 15
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Sports & leisure - Cork, flax and green epoxy: a perfect balance for a skateboard
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Medical - Lightweight emergency medical cot
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 18
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Natural fibres - Tending towards optimism
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 20
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 21
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Interview - MIT-NECST Lab: a research consortium dedicated to composites in Aeronautics
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 23
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Conferences - Gain insight into the JEC 2015 Forums conferences programme
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 25
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Wind energy - Double-digit growth continues
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 27
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Design - A wind turbine without blades
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Simulation - Visualizing RTM behaviour using advanced 3D CAE technology
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 30
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 31
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 32
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Permeability - Optimizing fabrics for wind blade infusion
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 34
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Automation - Automation strategies in rotor blade production: preforming vs. direct textile layup
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 36
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 37
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Recycling - Recycling decommissioned composite wind blades
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Platform - An internet aid for advances in wind turbine blade design
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 40
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Graphene - Gambling with graphene, will it pay off ?
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 42
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 43
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 44
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Thermal expansion - Boeing simulates thermal expansion in composites with expanded metal foil for lightning protection of aircraft structures
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 46
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 47
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Heating - Power transfer in complex shape heated moulds or functional composites
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 49
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 50
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 51
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Manufacturing - Tension control in composites manufacturing
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 53
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 54
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 55
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 56
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 57
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 58
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 3D printing - A fully biodegradable flax fibre-reinforced thermoplastic filament for 3D printing
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 60
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 61
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - RTM/LCM - Fast production epoxies for lightweight automotive composites
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 63
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 64
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - Index
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - In the world
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 67
JEC COMPOSITES MAGAZINE - Issue #99 - September 2015 - 68
https://www.nxtbook.fr/newpress/jeccomposites/jcm2211_148
https://www.nxtbook.fr/newpress/jeccomposites/jcm2209_147
https://www.nxtbook.fr/newpress/jeccomposites/jcm2206_146
https://www.nxtbook.fr/newpress/jeccomposites/jcm2204_145
https://www.nxtbook.fr/newpress/jeccomposites/jcm2201_144
https://www.nxtbook.fr/newpress/jeccomposites/jcm211_143
https://www.nxtbook.fr/newpress/jeccomposites/jcm2109_142
https://www.nxtbook.fr/newpress/jeccomposites/jcm2107_141
https://www.nxtbook.fr/newpress/jeccomposites/jcm2105_140
https://www.nxtbook.fr/newpress/jeccomposites/jcm2103_139
https://www.nxtbook.fr/newpress/jeccomposites/jcm-experts-digest-additive-manufacturing-2020
https://www.nxtbook.fr/newpress/jeccomposites/jcm2101_138
https://www.nxtbook.fr/newpress/jeccomposites/jcm2011_Special_Issue4
https://www.nxtbook.fr/newpress/jeccomposites/jcm2011_137
https://www.nxtbook.fr/newpress/jeccomposites/jcm2009_136
https://www.nxtbook.fr/newpress/jeccomposites/jcm2007_135
https://www.nxtbook.fr/newpress/jeccomposites/jcm_2020_Q1_Innovation_Report
https://www.nxtbook.fr/newpress/jeccomposites/jcm2005_Special_Issue3
https://www.nxtbook.fr/newpress/jeccomposites/jcm2005_134
https://www.nxtbook.fr/newpress/jeccomposites/jcm2003_133
https://www.nxtbook.fr/newpress/jeccomposites/jcm2001_132
https://www.nxtbook.fr/newpress/jeccomposites/jcm1911_Special_Issue2
https://www.nxtbook.fr/newpress/jeccomposites/jcm1911_131
https://www.nxtbook.fr/newpress/jeccomposites/jcm1909_130
https://www.nxtbook.fr/newpress/jeccomposites/jcm1907_129
https://www.nxtbook.fr/newpress/jeccomposites/jcm1905_128
https://www.nxtbook.fr/newpress/jeccomposites/jcm1903_Special_Issue1
https://www.nxtbook.fr/newpress/jeccomposites/jcm1903_127
https://www.nxtbook.fr/newpress/jeccomposites/jcm1901_126
https://www.nxtbook.fr/newpress/jeccomposites/jcm1811_125
https://www.nxtbook.fr/newpress/jeccomposites/jcm1810_124
https://www.nxtbook.fr/newpress/jeccomposites/jcm1808_123
https://www.nxtbook.fr/newpress/jeccomposites/jcm1807_122
https://www.nxtbook.fr/newpress/jeccomposites/jcm1805_121
https://www.nxtbook.fr/newpress/jeccomposites/jcm1804_120
https://www.nxtbook.fr/newpress/jeccomposites/jcm1803_119
https://www.nxtbook.fr/newpress/jeccomposites/jcm1802_119-Supplement_Innovation_Report
https://www.nxtbook.fr/newpress/jeccomposites/jcm1801_118
https://www.nxtbook.fr/newpress/jeccomposites/jcm1711_117
https://www.nxtbook.fr/newpress/jeccomposites/jcm1710_116
https://www.nxtbook.fr/newpress/jeccomposites/jcm1708_115
https://www.nxtbook.fr/newpress/jeccomposites/jcm1707_114
https://www.nxtbook.fr/newpress/jeccomposites/jcm1706_113
https://www.nxtbook.fr/newpress/jeccomposites/jcm1704_112
https://www.nxtbook.fr/newpress/jeccomposites/jcm1703_111
https://www.nxtbook.fr/newpress/jeccomposites/jcm1701_110
https://www.nxtbook.fr/newpress/jeccomposites/jcm1611_109
https://www.nxtbook.fr/newpress/jeccomposites/jcm1610_108
https://www.nxtbook.fr/newpress/jeccomposites/jcm1608_107
https://www.nxtbook.fr/newpress/jeccomposites/jcm1607_106
https://www.nxtbook.fr/newpress/jeccomposites/jcm1605_105
https://www.nxtbook.fr/newpress/jeccomposites/jcm1604_104
https://www.nxtbook.fr/newpress/jeccomposites/jcm1603_103
https://www.nxtbook.fr/newpress/jeccomposites/jcm1601_102
https://www.nxtbook.fr/newpress/jeccomposites/jcm1511_101
https://www.nxtbook.fr/newpress/jeccomposites/jcm1510_100
https://www.nxtbook.fr/newpress/jeccomposites/jcm1509_99
https://www.nxtbook.fr/newpress/jeccomposites/jcm1507_98
https://www.nxtbook.fr/newpress/jeccomposites/jcm1505_97
https://www.nxtbook.fr/newpress/jeccomposites/jcm1504_96
https://www.nxtbook.com/newpress/jeccomposites/jcm1503_95
https://www.nxtbook.com/newpress/jeccomposites/jcm1501_94
https://www.nxtbook.com/newpress/jeccomposites/jcm1412_93
https://www.nxtbook.com/newpress/jeccomposites/jcm1410_92
https://www.nxtbook.com/newpress/jeccomposites/jcm1409_91
https://www.nxtbook.com/newpress/jeccomposites/jcm1406_90
https://www.nxtbook.com/newpress/jeccomposites/jcm1405_89
https://www.nxtbook.com/newpress/jeccomposites/jcm1404_88
https://www.nxtbook.com/newpress/jeccomposites/jcm1403_87
https://www.nxtbook.com/newpress/jeccomposites/jcm1401_86
https://www.nxtbook.com/newpress/jeccomposites/jcm1311_85
https://www.nxtbook.com/newpress/jeccomposites/jcm1310_84
https://www.nxtbook.com/newpress/jeccomposites/jcm1308_83
https://www.nxtbook.com/newpress/jeccomposites/jcm1307_82
https://www.nxtbook.com/newpress/jeccomposites/jcm1305_81
https://www.nxtbook.com/newpress/jeccomposites/jcm1304_80
https://www.nxtbook.com/newpress/jeccomposites/jcm1303_79
https://www.nxtbook.com/newpress/jeccomposites/jcm1301_78
https://www.nxtbook.com/newpress/jeccomposites/jcm1212_77
https://www.nxtbook.com/newpress/jeccomposites/jcm1210_76
https://www.nxtbook.com/newpress/jeccomposites/jcm1208_75
https://www.nxtbook.com/newpress/jeccomposites/jcm1207_74
https://www.nxtbook.com/newpress/jeccomposites/jcm1206_73
https://www.nxtbook.com/newpress/jeccomposites/jcm1204_72
https://www.nxtbook.com/newpress/jeccomposites/jcm1203_71
https://www.nxtbook.com/newpress/jeccomposites/jcm1201_70
https://www.nxtbook.com/newpress/jeccomposites/jcm1111_69
https://www.nxtbook.com/newpress/jeccomposites/jcm1110_68
https://www.nxtbook.com/newpress/jeccomposites/jcm1108_67
https://www.nxtbook.com/newpress/jeccomposites/jcm1107_66
https://www.nxtbook.com/newpress/jeccomposites/jcm1105_65
https://www.nxtbook.com/newpress/jeccomposites/jcm1104_64
https://www.nxtbook.com/newpress/jeccomposites/jcm1103_63
https://www.nxtbook.com/newpress/jeccomposites/jcm1101_62
https://www.nxtbook.com/newpress/jeccomposites/jcm1011_61
https://www.nxtbook.com/newpress/jeccomposites/jcm1010_60
https://www.nxtbook.com/newpress/jeccomposites/jcm1009_59
https://www.nxtbook.com/newpress/jeccomposites/jcm1006_58
https://www.nxtbook.com/newpress/jeccomposites/jcm1005_57
https://www.nxtbook.com/newpress/jeccomposites/jcm1004_56
https://www.nxtbook.com/newpress/jeccomposites/jcm1003_55
https://www.nxtbook.com/newpress/jeccomposites/jcm1001_54
https://www.nxtbook.com/newpress/jeccomposites/jcm0911_53
https://www.nxtbook.com/newpress/jeccomposites/jcm0910_52
https://www.nxtbook.com/newpress/jeccomposites/jcm0909_51
https://www.nxtbook.com/newpress/jeccomposites/jcm0907-08_50
https://www.nxtbook.com/newpress/jeccomposites/jcm0906_49
https://www.nxtbook.com/newpress/jeccomposites/jcm0904_48
https://www.nxtbook.com/newpress/jeccomposites/jcm0903_47
https://www.nxtbook.com/newpress/jeccomposites/jcm0901_46
https://www.nxtbook.com/newpress/jeccomposites/jcm0811_45
https://www.nxtbook.com/newpress/jeccomposites/jcm0810_44
https://www.nxtbook.com/newpress/jeccomposites/jcm0809_43
https://www.nxtbook.com/newpress/jeccomposites/jcm0807_42
https://www.nxtbook.com/newpress/jeccomposites/jcm0806_41
https://www.nxtbook.com/newpress/jeccomposites/jcm0805_40
https://www.nxtbook.com/newpress/jeccomposites/jcm0803_39
https://www.nxtbook.com/newpress/jeccomposites/jcm0801_38
https://www.nxtbook.com/newpress/jeccomposites/jcm0712_37
https://www.nxtbook.com/newpress/jeccomposites/jcm0710_36
https://www.nxtbook.com/newpress/jeccomposites/jcm0709_35
https://www.nxtbook.com/newpress/jeccomposites/jcm0707_34
https://www.nxtbook.com/newpress/jeccomposites/jcm0706_33
https://www.nxtbookmedia.com